• VM600 ABE040 204-040-100-011 应用机架式VM600系列工控备框架

• ——- Contact us for the spare parts of the side door——————
  

• 
  

• ——- Contact us for spare parts of the cold door——————

• 
  

• ——- Contact us for discontinued spare parts——————

• 
  

CMC 16状态监测卡是中央振动计VM600系列条件下的元件监控系统（CMS）。该智能前端数据采集单元（DAU）与VM600 CMS软件一起使用

获取、分析结果并将结果传输给主机通过VM600系列CPU M模块以太网控制器或直接通过串行链路。输入完全可编程，可接受表示速度、相位参考、速度和速度的信号，振动（加速度、速度或位移），动态压力、气隙转子和磁极轮廓，任何动态信号或任何准静态信号。信号可以从相邻的机械保护输入通过VM600“原始总线”和“Taco”的卡（MPC 4）总线或通过螺纹端子连接器外部在国际奥委会16T上。IOC 16T模块还提供信号调节和EMC保护，并允许要路由到CMC 16的输入，包括16可编程跟踪抗锯齿滤波器，以及模数转换器（ADC）。在船上处理器处理采集的所有控制，从时域到频域的转换（快速傅里叶变换），频带提取，单位转换、限额检查和通信主机系统。16个可单独配置的动态通道16个并行可编程抗混叠滤波器和模数转换器前4个通道也可配置为测速输入后12个通道也可配置为进程价值观VME架构可配置的同步和异步取样，取样高分辨率3200线FFT10个完全可配置的处理输出信道，可以是频带或基于时域的输出每个处理输出6个可配置报警磁滞死区基于“报警”和“异常”的计划车载缓冲存储器前面板上的三色LED指示状态使用自动插入/取出卡配置以太网和串行RS-4851通信。VM600Mk2和VM600系统机架，用于容纳机械保护和/或状态监测系统坚固的铝制结构多可容纳两个RPS6U机架电源（交流输入和/或直流输入）的空间，以支持机架电源冗余多可容纳12个处理卡和电源检查继电器提供标准、独立电路（IEC 60255-5）、cCSAus（IEC 61010-1）和保形涂层版本高质量、高可靠性19〃6U机架，用于容纳VM600Mk2/VM600机架式机械监控系统。多可容纳12个机械监控卡（机械保护、状态监控和/或燃烧监控）、多2个电源（用于电源冗余）、机架控制器和通信接口卡以及电源检查继电器。坚固的铝制结构，适用于恶劣环境。

VM600 ABE040 204-040-100-011 应用机架式VM600系列工控备框架

The Company:

Spare parts module of PLC and DCS system

 Allen Bradley (American AB) series products

(Modicon Electric) Series Products

 General electric series products

Westinghouse Series Products

Sales of ABB Robots FANUC Robots、YASKAWA Robots、KUKA Robots、Mitsubishi Robots、OTC Robots、Panasonic Robots、MOTOMAN Robots

estinghouse: spare parts for OVATION system, WDPF system and MAX1000 system.

Invensys Foxboro: IA Series system, FBM (field I/O module) sequence control, ladder logic control, accident recall processing, digital analog conversion, I/O signal processing, data communication and processing, etc. Invensys Triconex redundant fault tolerant control system, modern fault-tolerant controller based on triple module redundancy (TMR) structure.

Bosch Rexroth: Indramat, IO module, PLC controller, drive module, etc.

Motorola: MVME 162, MVME 167, MVME1772, MVME177 and other series.

• VM600Mk2 and VM600 system racks to house machinery protection and/or condition monitoring systems

• Robust aluminium construction

• Space for up to two RPS6U rack power supplies (AC-input and/or DC-input) to support rack power supply redundancy

• Space for up to 12 processing cards and power supply check relay

• Available in standard, separate circuits (IEC 60255-5), cCSAus (IEC 61010-1) and conformally coated versions

The 10 available outputs per channel can include RMS, peak, peak-peak, true peak, true peak-peak values, Gap, Smax, or any configurable band based upon synchronous or asynchronously acquired spectra. Acceleration (g), velocity (in/sec, mm/sec) and displacement (mil, micron) signals are catered for and can be converted for display to any standard. If configured, data is sent to the host computer only on exception, for example, only if the change of value exceeds a pre-defined threshold. Values can also be averaged for smoothing or noise reduction. Events are generated when values exceed one of the 6 configurable limits, exceed rate-of-change alarms or deviate from stored baselines. However, adaptive monitoring techniques can also be employed to dynamically adjust alarm set points based upon machine parameters such as speed and load. Machine start-ups, shutdowns and overspeeds are detected from checks of speed reference against configured trigger levels. In Transient Mode, higher density logging is available based upon configurable time and speed intervals. Vibration measurement and logging is achieved in speed ranges from 15 rev/min to 30,000 rev/min. The CMC 16 acquires and processes high-resolution data captured at scheduled intervals or on alarm detection (waveforms, spectra and orbits). Spectral resolution, frequency span or order span, window type, averaging mode and number of averages are fully configurable. The capacity also exists to trigger extended capture of time-based data over several minutes using an ‘Oscilloscope Mode’ as this can provide valuable data, particularly during machine start-up.1 For specific applications, contact your Vibro-Meter representative.

Vibro-meter VM600 CMC16 

Vibro-meter VM600 ABE040 

REXA SMB9215-1E-1-7725 

MTL 8206-TI-IS 

BENTLY 3500/62 

BENTLY 3500/92 136180-01 

BENTLY 3500/15 127610-01 

YOKOGAWA UP5***-001-11-00 

NI SCXI-1193 

BENTLY 3500/42M-01-00 

YOKOGAWA ISC40G-TF-T1-05 

ABB YPK117A 61163280 

A-B 1756-L73S/B 

ABB DNC115 

ABB DKL032 

EATON XVS-440-10MPI-1-10

Stein sohn F404002A

FOXBORO FBM230 P0926GU 

FOXBORO FBM233 P0926GX

Vibro-meter VM600-ABE040 204-040-100-011 

Vibro-meter 200-595-100-014 200-595-072-122 VM600 CPUM 

Vibro-meter 600-003 620-001-001-116 VM600 XMV16 

Vibro-meter 620-002-000-113 620-003-111-112 VM600 XI016T 

VM600 ABE040 204-040-100-011 应用机架式VM600系列工控备框架